第一句子网 - 唯美句子、句子迷、好句子大全
第一句子网 > 风扇罩 fan cowl英语短句 例句大全

风扇罩 fan cowl英语短句 例句大全

时间:2021-01-09 02:22:43

相关推荐

风扇罩 fan cowl英语短句 例句大全

风扇罩,fan cowl

1)fan cowl风扇罩

英文短句/例句

1.Set fan shroud aside.将风扇罩置于它处。

2.Install power steering reservoir to fan shrou安装动力转向储液罐至风扇罩。

3.Be sure of at least 25 mm (0 inches) between tips of fan blades and fan shrou确认风扇叶轮与风扇罩之间至少有25公厘(0英寸)的间隙。

4.Install the fan shroud, electric cooling fan and radiator and condenser (if equipped with A/C).安装风扇罩、电动冷却风扇、散热器和冷凝器(如果配备有空调)。

5.Detach power steering reservoir from fan shroud and lay aside.将动力转向储液罐同风扇罩分开并放至一边。

6.Remove the four fan shroud to core support mounting screws.拆卸四个风扇罩至中心支架的固定螺丝。

7.Disconnect CRS hose from radiator filler neck and pull through (remove) the shroud retaining loops.从散热器填注颈上断开CRS软管,并从风扇罩保护套环上将其拔(拆)下。

8.ring-mouted fan with a self-contained electric motor of an output not exceeding 125w安有环形罩的风扇,自备电机输出功率不超过125w

9.industrial hood incorporating a fan with maximum horizontal side not exceeding 120cm工业用排气罩,装有风扇,最大水平面不超过120cm

10.laboratory hood incorporating fan with maximum horionatal side not exceeding 120cm实验室用排气罩,装有风扇,最大水平面不超过120cm

11.recycling hood incorporating a fan with mazimum horizontal side exceeding 120cm循环排气罩,带有风扇,最大水平面不超过120cm

12.Numerical Simulation and Experiment Research of the Air Condition Axial Fans Matching the Shroud;空调风扇及其导风罩匹配的数值模拟与实验研究

13.Electric Fan, Powerful fan, Ventilating Fan, etc. are our main products.电风扇,强力风扇,换气扇等,是我们主要的产品。

14.A metal cover or cowl for a hearth or stove.排风罩用于炉床或炉子的金属盖或罩

15.If you"re hot and you know it, fan your face.如果感到炎热,你就扇扇风。

16.The fan blades cannot be repaireIf the fan is damaged, it must be replaceInspect the fan blades as follows:不能修理风扇叶片。如果风扇损坏,必须更换。检查风扇叶片如下:

17.A windscreen for a chimney.烟囱罩烟囱的挡风屏

18.Rothemuhle regenerative air preheater风罩再生式空气预热器

相关短句/例句

fan guard风扇护罩

3)lampshade of electric fan电风扇灯罩

1.By researching the design of injection mould forlampshade of electric fan, the eccentricity of locking force and bulging force, in the design of injection mould for a cavity per mould, was resloved.通过对电风扇灯罩注塑摸具的设计探讨,解决了一模一腔注塑模设计中常遇到的锁模力与胀模力偏心问题,并对外观质量要求高的透明注塑件的注塑模具设计中浇注系统的结构设计、尺寸计算,推出机构的结构设计和模具总体结构设计进行了探讨,找到了解决问题的方法。

4)blower armor hood;风扇装甲罩;

5)cooling fan housing冷却风扇罩

6)fan fairing风扇整流罩

延伸阅读

风扇①热天取凉的旧式用具,用布制成,吊在梁上,用人力拉动生风。②电扇。

本内容不代表本网观点和政治立场,如有侵犯你的权益请联系我们处理。
网友评论
网友评论仅供其表达个人看法,并不表明网站立场。