筒压法,cylinder-mould testing method
1)cylinder-mould testing method筒压法
1.A study on thecylinder-mould testing method for the compressive strength of the mortar with highly fine-grained sand;筒压法检测特细砂水泥砂浆抗压强度的试验研究
1.Contrastive Analysis and Experimental Research on Mortar Strength with the Methods of Column Compression and Point Load点荷法、筒压法检测砂浆强度试验研究及对比分析
2.Pneumatic Jacking Inverted Construction for 240 m Stack Inner Steel Cylinder240m烟囱钢内筒气压顶升倒装施工法
3.Up-side-down Hydraulic Lifting Construction of the Internal Steel Barrel of High Chimney高烟囱钢内筒液压提升倒装施工方法
4.Research on the Three-dimensional Computing Method of Earth Pressure for Large-diameter Cylinder;大直径薄壳圆筒结构筒后土压力的空间计算方法
5.The flat container is important tool for extruding large-sized aluminum wallboard. The kinds of flat containers, the design method and strength computing were introduced.扁挤压筒是挤压大型铝壁板的重要工具。介绍了扁挤压筒类型、计方法和强度计算。
6.Optimal Design of Multilayer Autofretted High Pressure Chamber of Water Cannon水炮的多层自增强高压腔筒的优化设计方法
7.Research on the Method of Wellbore Temperature and Pressure Calculation during Deep-water Drilling;深水钻井环境下的井筒温度压力计算方法研究
8.FINITE ELEMENT SOLUTION OF SCROLL PRESSURE OF DOWN-COILER FOR HOT STRIP MILL;带钢热连轧地下卷取机卷筒压力的有限元解法
9.Reinforced Concrete Based on Cylinder Wall Construction Method of Hydraulic Research Slipform基于钢筋混凝土筒壁液压滑模施工工法研究
putational Method of Pressure Distribution of Printing Ink between Two Rollers of Printer辊状印刷机滚筒间油墨压力分布计算方法
11.REINFORCEMENT CALCULATION METHOD FOR LARGE OPENING PRESSURE CYLINDER VESSEL WITH FLANGE CONNECTION带法兰接管的压力容器圆筒大开孔补强计算方法
12.central cylinder印花大锡林（辊筒印花机的承压大辊筒）
13.INSTRUCTION: 1.PRESS BUTTON ON BOTTOM, TURN IT ON/OFF.使用方法:按/压手电尾部按钮，即可打开/关闭手电筒。
14.Study on Deflection of Impression Cylinder and Active Compensation Method;胶印机压印滚筒挠曲变形分析及主动补偿方法研究
15.Reliability Analysis of the Internal Steel Stacks Installation in Multi-flue Chimney Based on the Hydraulic Lifting Upside-down Method;基于液压提升倒装法的多管式烟囱钢内筒安装可靠性分析
16.The Research of the Bracket Deformation and Processing Method in Pressure Welding System of Missile Semi-Cylinder导弹半筒压力焊接系统中托架变形及处理方法研究
17.Research and Development on Processing Equipment for Welding of Flange Hole on Pressure Vessel Shell压力容器筒体焊接法兰孔加工装置的研究与开发
18.Analysis of backward ball spinning of thin-walled tube part with longitudinal inner ribs based on FEM基于有限元法纵向内筋薄壁筒反向滚珠旋压分析
相关短句/例句
pressure sleeve压筒
3)biased ion collector array偏压法拉第筒阵列
4)controlling methods of wellbore pressure井筒压力控制方法
5)diffusing cartridge传压筒
1.Under the environment in which diffusing exists,an accessory of pressure testing system with capillary,being difficult to test and needing frequent blowing,we developed a pressure-testing anddiffusing cartridge.针对现有毛细管测压系统的配套工具———传压筒上部无法方便试压,且下入过程需频繁吹扫的缺陷,研制了可试压检查传压筒,其活塞可承受下压,可通过活塞上剪钉的数量来控制传压筒试压压力的大小。
6)cylindrical compress strength筒压强度
1.Using orthogonality testing method and single factor analysis,activator,additive,water ratio and technological conditions effect on non-sintered ceramsitecylindrical compress strength were discussed.采用正交实验法,结合单因素分析,研究了激发剂、外加剂和水固比等因素和工艺条件对免烧陶粒筒压强度等性能的影响。
延伸阅读
拔筒法拔筒法 拔筒法 拔罐法。见《外科正宗》卷二“脑疽应用方”。参见拔罐法条。
